以用户为中心的可见光通信协作传输中训练资源分配算法

以用户为中心的可见光通信协作传输是近年来出现的新架构,这导致虚拟小区之间出现重叠。为避免导频污染问题,每个虚拟小区中的光接入点(AP)或者虚拟小区中选择相同AP的用户发送的训练序列应该是正交的。针对可见光通信中以用户为中心的协作网络,研究训练资源的正交分配问题,提出了一种新的导频分配算法,联合导频分配和用户选择问题,以期最大限度地增加虚拟小区内可被接入的用户数。分析和仿真结果表明,该导频分配方案可以有效改善导频污染问题,提高训练资源利用率,并且相比已有的导频分配方案,性能有所改进。     

化妆品功效评价(Ⅵ)——化妆品人体功效评价的实验设计

概述了化妆品人体功效评价实验设计的概念、基本要素和基本原则,介绍了常用实验设计类型和实验设计要点,提供了人体功效评价实验方案设计的思路,有助于提高研究者制定实验设计方案的水平。     

A design of experiments investigation into dry separation using a Knelson Concentrator

Enhanced gravity, or centrifugal, separators have revolutionised gold processing over the past decades, significantly increasing the recovery of fine (−100 μm) free gold. One of the main drawbacks of centrifugal gravity concentrators is the large volume of water required (even if it is all recycled). With water becoming an ever increasingly important “commodity”, reducing this is of importance both from an environmental and a monetary point of view. This work investigated operating a laboratory scale Knelson Concentrator with a dry feed and using air as the fluidising medium. The feed used was a synthetic mixture of tungsten and quartz, used to mimic a gold ore. The response surface method and central composite design techniques were used to design the experiments and to model the results, with the experimental variables being the bowl speed (G-Level), air fluidising pressure and the feed rate. The models corresponded well to the experimental results, indicating that for this experimental setup, the optimal conditions were a bowl G-Level of 40 G, a feed rate of 220 g/min and an air fluidising pressure of 8 psi.     

Material design and development: From classical thermodynamics to CALPHAD and ICME approaches

This paper presents an overview and examples of material design and development using (1) classical thermodynamics; (2) CALPHAD (calculation of phase diagrams) modeling; and (3) Integrated Computational Materials Engineering (ICME) approaches. Although the examples are given in lightweight aluminum and magnesium alloys for structural applications, the fundamental methodology and modeling principles are applicable to all materials and engineering applications. The examples in this paper have demonstrated the effectiveness and limitations of classical thermodynamics in solving specific problems (such as nucleation during solidification and solid-state precipitation in aluminum alloys). Computational thermodynamics and CALPHAD modeling, when combined with critical experimental validation, have been used to guide the selection and design of new magnesium alloys for elevated-temperature applications. The future of material design and development will be based on a holistic ICME approach. However, key challenges exist in many aspects of ICME framework, such as the lack of diffusion/mobility databases for many materials systems, limitation of current microstructural modeling capability and integration tools for simulation codes of different length scales.     

Improved method for roadside barrier length of need modeling using real-world trajectories

The 2011 AASHTO Roadside Design Guide (RDG) contains perhaps the most widely used procedure for choosing an appropriate length of need (LON) for roadside barriers. However, this procedure has several limitations. The procedure uses a highly simplified model of vehicle departure, and the procedure does not allow designers to specify an explicit level of protection. A new procedure for choosing LON that addresses these limitations is presented in this paper. This new procedure is based on recent, real-world road departure trajectories and uses this departure data in a more realistic way. The new procedure also allows LON to be specified for a precisely known level of protection – a level which can be based on number of crashes, injury outcomes or even estimated crash cost – while still remaining straightforward and quick to use like the 2011 RDG procedure.     

Design and optimization of ceramic membrane structure: From the perspective of flux matching between support and membrane

The support flux was first investigated as a separate influencing factor for its effect on performances of ceramic filtration membranes. Three pre-membranes were prepared by tape-casting and then transfer-coated to supports to form dual-layer ceramic membranes after sintering. Experiments demonstrated that membrane layers with almost the same properties were obtained despite the huge difference in support flux. When the support flux increases from 3.120 to 97.53 m³m^?2h^?1, the flux of these three membrane series have increased by 75%, 186% and 228%, respectively. Experimental rules can provide structural design and evaluation from the perspective of permeability. The limit membrane flux of a certain system was derived according to the resistance distribution law of internal membrane structure and the Darcy's theorem. On this basis, a method for designing support flux was proposed. Furthermore, we present a criterion to quickly and easily evaluate the match between the support and the top layer, which is the ratio of membrane resistance to total resistance. Finally, the filtration resistance of penetration caused by suction of membrane particles into the support was measured for the first time, taking the advantage of the transfer-coating method that inherently free of penetration. Our works are expected to deepen the understanding of the ceramic membrane structure and provided guidance for its rational design and optimization.     

基于学生群体心理测试系统的设计

心理测试的根本目的是为了让人们在测试过程中，产生某些特定行为，即个体对测试题目的反应，并根据这些行为反应来推论其相应的心理特性。在一定程度上帮助我们了解人类的心理活动，并从中得到帮助。因此，本文对基于学生群体心理测试系统的设计进行深入研究。     

汽车雨挡导流片浮顶式侧抽芯机构注射模设计

介绍了一款汽车雨挡导流片异型塑件两板注射模的结构设计,该模具基于采用常规的滑块抽芯机构及斜顶机构难以实现塑件完全脱模的机构设计困难问题,突破常规设计思路,设计了一种型芯浮顶式侧抽芯机构来实现塑件的自动化注射生产。机构中,在模具开模打开后,通过顶出板及顶杆将塑件和部分成型一同顶出,而后再通过侧边二次顶出机构将塑件从局部型芯上顶出而实现塑件的完全脱模,有效地简化了模具结构设计,降低了模具的加工制造难度,降低了模具的制造成本,模具结构复杂新颖,工作稳定可靠,为异型类塑件的模具结构及机构设计创新设计提供了一个较好的案例借鉴。